Glossary: pellet and solid biomass certification

Over 40 terms used in audits, scheme documents and test reports — from ENplus and mass balance to PoS, fine fraction and first gathering point.

This glossary of pellet and biomass certification contains definitions of terms found in quality schemes (ENplus, DINplus) and sustainability schemes (SURE, KZR INiG) as well as in the FSC supply chain — from fuel parameters such as NCV or mechanical durability to organisational concepts such as mass balance, traceability or system boundary. The definitions are explanatory; the binding sources are always the current scheme documents and standards.

In brief

  • 43 terms in alphabetical order — from agro pellet to wood raw material
  • Quality schemes: ENplus, DINplus — fuel parameters under EN ISO 17225-2
  • Sustainability schemes: SURE, KZR INiG, RED II/III, GHG, mass balance
  • Supply chain: FSC, service certificate, PoS, first gathering point

Jump to a letter

A · B · C · D · E · F · G · I · K · M · N · P · R · S · T · W

A

Agro pellet
Pellet produced from agricultural feedstocks, e.g. sunflower husks, straw or nut shells, classified under EN ISO 17225-6. It usually has a higher ash content than wood pellets, so it is directed to boiler plants adapted to burn it.
Ash content
The content of residue remaining after combustion of the fuel, in percent. For class A1 wood pellets it must not exceed 0.7% (A2: 1.2%, B: 2.0%) — high ash reduces boiler efficiency and increases operating costs.

B

Batch
A defined quantity of product with uniform characteristics, covered by a common designation and quality test. The batch is the unit of traceability — results and sales are documented at batch level.
Big-bag
A flexible container (FIBC) typically holding 500–1500 kg of pellets. It protects against moisture, but every transloading increases the share of fine fraction, which is why it requires procedures and quality control.
Biomass supply chain
The sequence of actors from the producer, through collection points, transport, warehouses and traders, to the industrial user. Every link that physically takes over the product may require its own certification scope — see Supply chain.
Bulk density
The mass of bulk pellets per unit of volume, in kg/m³. For class A1 under EN ISO 17225-2 it is at least 600 kg/m³ — a parameter important for logistics, silos and commercial conversion factors.

C

Certification
A process in which an independent certification body confirms the conformity of a product or organisation with the requirements of a chosen scheme. A consultant prepares the organisation for the audit, but the decision to issue the certificate is made solely by the body.
Certification body
An independent organisation conducting audits and making decisions on issuing, maintaining or withdrawing a certificate. It must be approved by the scheme owner (e.g. EPC, DIN CERTCO, SURE-EU, KZR INiG) and is usually accredited to ISO/IEC 17065.

D

DIN+
The former German quality mark for wood fuels (based on DIN 51731), the predecessor of DINplus. It still appears in older contracts and documents, but certification today follows the current DIN CERTCO programme.
DINplus
A wood pellet quality certification programme run by DIN CERTCO, particularly valued in Germany and Austria. The requirements are close to ENplus class A1 — including ash ≤0.7% and mechanical durability ≥97.5%. Details: the DINplus page.

E

EN ISO 17225-2
The standard defining wood pellet quality classes: A1, A2 and B. Limit values for A1 include ash ≤0.7%, NCV ≥16.5 MJ/kg, mechanical durability ≥97.5% and bulk density ≥600 kg/m³.
ENplus
The world's most recognised wood pellet quality certification scheme, managed by EPC, with classes A1/A2/B. It covers production, trading and services — full description on the ENplus page.
EPC (European Pellet Council)
An organisation within Bioenergy Europe that manages the ENplus scheme: it licenses certification bodies, maintains the certificate register and issues scheme documents.

F

Fine fraction
The share of dust and fines below 3.15 mm in pellets. For bagged pellets of classes A1/A2/B under EN ISO 17225-2 it must not exceed 1%; for bulk deliveries the limit is set by scheme documents and contracts with the buyer.
Finished product
Product after completion of all production processes, ready for release to the customer. It must not be released before quality control approval — and after release it is subject to batch traceability.
First gathering point
The first point collecting biomass from feedstock producers — the entity that starts the conformity reporting chain in sustainability schemes (including KZR INiG) and is responsible for gathering declarations from feedstock suppliers.
FSC (Forest Stewardship Council)
An international certification scheme for forest management (FM) and the wood supply chain (CoC). In the pellet industry it confirms legality and responsible sourcing of wood — see FSC and Dobry Pellet.
FSC Controlled Wood
FSC requirements for wood from uncertified sources: the organisation verifies a low risk of illegal logging, human rights violations and forest degradation before the material enters a mixed product.
FSC Mix
A label for products containing FSC-certified material, material from controlled sources (Controlled Wood) and/or reclaimed material, with a demonstrated percentage share. It requires an implemented mass balance.

G

Gap analysis
Gap analysis: a review of the organisation against the requirements of a chosen certification scheme, ending with a report of gaps and an action schedule. It is the standard first step of cooperation — described on the Services page.
GHG (greenhouse gases)
Greenhouse gases; in sustainability schemes (SURE, KZR INiG) the GHG emission saving of biomass fuel against the fossil fuel comparator is calculated and reported to industrial users.

I

INSTAL
An abbreviation encountered in contracts and documents of the heating industry; it is not the name of a certification scheme. When signing a contract, always verify the full name and status of the body in the register of the chosen scheme (e.g. ENplus, KZR INiG).
Internal audit
An audit performed by the organisation itself (or its consultant) before the external audit, to assess implementation of the requirements. It ends with a protocol listing nonconformities and a corrective action plan — see our audit services.

K

KOBiZE
Poland's National Centre for Emissions Management (Krajowy Ośrodek Bilansowania i Zarządzania Emisjami) — it operates the national emissions registry and reporting systems, in which installations demonstrate the sustainability of combusted biomass on the basis of certificates and PoS declarations.
KZR INiG
The Polish national sustainability scheme (Krajowy System Zrównoważoności) run by the Oil and Gas Institute — National Research Institute, recognised against RED II for biofuels, biomass fuels and RFNBO. The certificate is issued by an approved certification body — details: KZR INiG.

M

Management representative
The person appointed by management to coordinate the certification scheme: maintaining documentation, contact with the certification body and audit preparation. The role requires training and knowledge of the scheme's requirements.
Mass balance
A chain-of-custody control method based on reconciling the quantities of certified material bought and sold over a reporting period (e.g. monthly or quarterly). It underpins the SURE, KZR INiG schemes and FSC models.
Mechanical durability
The resistance of the granulate to crumbling during transport and transloading, measured in a tumbler test. For class A1 it is at least 97.5% — low durability means more fine fraction and more complaints.

N

NCV (net calorific value)
Net calorific value — the calorific value of the fuel in MJ/kg, stated as received or on a dry basis. For class A1 wood pellets it is at least 16.5 MJ/kg; it is a key parameter in quality settlements with buyers.

P

Pellet press
A machine that compacts powdered feedstock in the openings of a die into granulate form. Its settings (feedstock moisture, die wear) directly affect the mechanical durability and fine fraction of the pellets.
PoS (Proof of Sustainability)
A sustainability declaration attached by a certified seller to every transaction covered by the SURE or KZR INiG scheme. Without a PoS, a batch cannot be reported as a sustainable fuel in RED and KOBiZE reports.

R

RED II
Directive (EU) 2018/2001 of the European Parliament on renewable energy, defining sustainability criteria for biomass used in energy generation. It is the basis of the SURE and KZR INiG schemes.
RED III
Directive (EU) 2023/2413 amending RED II — it raises renewable energy targets and tightens, among others, the criteria for forest biomass and the GHG emission reporting rules. Sustainability schemes are successively aligning their documents with it.

S

Service certificate
A certificate for entities performing services on pellets without producing them: bulk transport, storage, transloading (so-called service providers in ENplus). Conditions for individual links are described on the Supply chain page.
Solid biomass
Solid fuels of biological origin: wood pellets and briquettes, wood chips, agro pellets from sunflower husks or straw. In the energy sector it must meet the RED II/III sustainability criteria, confirmed by sustainability scheme certificates.
Sunflower husks
A residue of sunflower seed pressing, a feedstock for producing agro pellets for the energy sector. It has a higher ash content than wood pellets, which affects the class and the range of buyers.
Surveillance audit
A periodic audit conducted by the certification body after the certificate is issued — usually once a year — checking whether the organisation maintains conformity with the scheme's requirements. It is shorter than the certification audit, but overlooked nonconformities risk suspension of the certificate.
SURE
SUSTAINABLE RESOURCES Verification Scheme — a voluntary scheme compliant with RED II, confirming the sustainable use of biomass in the energy sector. It covers producers, collection points and traders — description: SURE.
System boundary
The defined scope of the organisation covered by the certificate: sites, production lines, activities (production, trading, services) and product groups. In the mass balance, the boundary determines the points of feedstock entry and product output.

T

Traceability
The ability to establish the history, use and location of a batch of pellets or biomass throughout the supply chain. It requires batch marking, recording of operations and consistent documentation.
Trader
An entity trading in pellets or biomass. To sell product as certified, it needs a trading scope in the given scheme (e.g. ENplus trading, SURE trader, KZR INiG) — even if it never stores the goods physically.

W

Wood chips
Mechanically shredded wood material of irregular shape, used as fuel in industrial boilers or as feedstock for pellet production. Quality classification follows EN ISO 17225-4.
Wood raw material
Wood material used for pellet production: sawdust, chips, roundwood or wood industry residues. In quality schemes its origin and purity (free of glues, varnishes, treated wood) are controlled at intake.

Where these terms are applied

Most of the entries come from the documents of specific certification schemes. To see the requirements in practice, go to the pages: ENplus (A1/A2/B), DINplus / DIN+, SURE, KZR INiG, FSC and Dobry Pellet, as well as the step-by-step certification process and the certification rules for the supply chain.

Frequently asked questions

Quality certification (ENplus, DINplus) confirms fuel parameters under EN ISO 17225-2 — ash, calorific value, durability. Sustainability certification (SURE, KZR INiG) confirms feedstock origin, mass balance and GHG emission savings required by RED II/III. One does not replace the other — many plants hold both certificates in parallel.

PoS stands for Proof of Sustainability — a sustainability declaration that a certified seller attaches to every transaction covered by the scheme (e.g. SURE or KZR INiG). Without a PoS, the batch cannot be reported as a sustainable fuel in RED and KOBiZE reports.

No — the glossary is explanatory and describes terms in a practitioner's language. Only the definitions and values contained in current standards (e.g. EN ISO 17225-2) and the scheme documents of ENplus, DINplus, SURE, KZR INiG and FSC are binding.

In the EN ISO 17225-2 standard (classes A1, A2, B) and in the documents of the chosen scheme — ENplus and DINplus publish their own parameter tables, which in some points are stricter than the standard. Before an audit always work on the latest edition of the document.

Service certificate and first gathering point — they show when a company performing services on pellets or biomass falls within the scope of certification. We describe the rules for each link on the Supply chain page.

A term from your documentation needs clarification?

We prepare plants for ENplus, DINplus, SURE, KZR INiG and FSC certification — we will explain the requirements on your own processes.

Ask a consultant